I am attempting to remove a space from a spherical solid and having no luck. In terms of primitives, I have a rectangular pyramid larger than the sphere with its tip at the center of the sphere attempting to remove every bit of the sphere within it while replacing the boundary outside with faces.
I managed to figure out how to segment and delete the face of the sphere where I wanted it, but not fill in the inside with new faces, so I gave up on that.
Any idea on how I should go about this? Picture attached:
https://preview.redd.it/id8wljtdxba81.png?width=1396&format=png&auto=webp&s=ee878381469f726bbf16c02c5d61adcda19dd58d
I've tried wrapping a patch around the frame and using sculpt but it gave me some error saying it wouldn't change anything that is until I messed with the dot and arrows and managed to delete the whole object. I've tried drawing lines on the surface of the sphere to segment it plus the lines deeper in, in the hopes that it would split it into a separate object I could delete to leave behind the cavity. That didn't work either. Like I said earlier, I then used those same lines plus the split tool to finally delete the section of face I wanted, but then I was left with the dimensionless cavity within. If I had the delete face tool also heal the section I wanted deleted afterward, then it just wouldn't delete the face, undoing what it had just done.
So I got a brand new A4 here, pressed load filament, filament is beign fed towards the nozzle , but then nothing its just sits there and the loading thing cancels without me pressing any buttons, its really trying though as you can hear a very audible clicking sound?
Not sure, kinda looks like its stuck before hitting the extruder somehow? but its brand new so there cant be any filament stuck in the nozzle or anything so... what to do?
Brand new to Cinema 4D and looking for some help with this issue. I brought in a 2D image as an AI file and extruded it out but I can't seem to figure out how to smooth out the pixelated edges as shown down below, Watched tons of videos and I'm just kinda stuck here. Anything helps!
https://preview.redd.it/cm1o19ddmbc81.png?width=1424&format=png&auto=webp&s=825c7e38f47e74ed201301bd4e32db722e3c103c
I have literally joined three lines in sketcher to form a triangle and every time I try to extrude it FreeCAD just extrudes the lines so it is a hollow shape. What do I need to do so it extrudes as a triangular prism>
https://preview.redd.it/d51sbcmpuia81.png?width=1474&format=png&auto=webp&s=a53ba354d3b5c301119ce3bd087bf915480a55a2
Hi guys, recently I installed the Bondtech upgrade to my mini and I've started to run into issues with the filament blobbing up and clogging the nozzle. I've...
-
Set and confirmed the Esteps (for me it was the default 415 that bondtech recommends)
-
Modified the retraction settings to their recommended 1.5mm length, 35mm/ retraction and detraction speed, 15% wipe
-
Tried it with the roll I was originally printing with, and a completely new roll (both matterhackers pro PLA)
-
Also tested the default retraction settings and some different retraction lengths and speeds (2mm length, 1mm length, 45mm/ speed, 60mm/ speed)
No matter what changes I seem to make, the filament will load and purge fine, but when I start printing it'll (sometimes) run the purge line correctly, but almost always will clog on the first few layers
I'm highly suspect that it's due to the retraction...but since prusa default and bondtech recommended both don't seem to work I'm at my wits end trying to figure out what could be the problem...
Any help would be greatly appreciated!
EDIT: thanks for all the suggestions! The issue was in fact due to the PTFE tubing not being set correctly. It prints like a charm now
