I am interested in setting up an aeroponics system but I haven't been able to find much info on the pros and cons of mister nozzles vs ultrasonic transducers. I know that mister nozzles can sometimes get clogged and some cannot create a fine enough mist. I read somewhere that there may be nutrient solution temperature issues with ultrasonic transducers. My choice is really narrowed down between Dewey Misters or ultrasonic transducers (haven't researched brands.) I am in northeast Florida and looking to grow some herbs (basil, cilantro, etc) on my balcony. Any advice would be greatly appreciated.
So I have an Iwata HP-CS Eclipse and I've been having some difficulties with getting paint to spray consistently. It doesn't seem to matter how thin I make it, how thick I make it, or what PSI I use. It will initially spray, then stop until I move the needle either back or forward then it will spray again. If I pull it back full blast it sprays in fits and starts. If I use plain water or isopropyl then it functions fine. Barely pull back the trigger and a trickle spray comes and is consistent. But the moment I use anything even remotely thicker then the issues arise.
I've tried Vallejo airbrush paint, the Iwata paint that came with it, craft paint, you name it. All paint is mixed with a paint mixer for at least 5 minutes before using. I've used it them from a consistency of thinned with airbrush thinner to the point of water to glooping straight from the craft paint tube. From 5 PSI up to 60. Still the same.
I've disassembled it and scrubbed all the parts down spotless so there isn't any clogging or residue between each test and no difference.
Any pointers of what I may be doing wrong?
https://preview.redd.it/g71ww35b3ga81.png?width=857&format=png&auto=webp&s=a09aae627b0e3e8e0050a754badd4ababd0f9414
3D Printing Resin vs Filament: Strength, Quality & Cost
Filament: Brands, Prices & Properties
Resin: Brands, Prices & Properties
Resin
- Most people can get away with using a $200 Photon Mono or Mars 2.
- Medium resin printers are an option if you need more build volume, but they cost more ($450+) initially + the replacement screen prices are higher.
- Large-sized resin printers are a thing but they are $1,300-1,700.
- Regardless of the size, the setup will need resin + supplies + ppe which can be an additional $100-200. Picking up a wash and cure or ultrasonic cleaner will be another $100+. These are not necessary but they do streamline post-processing.
- The high resolution resin printers are ideal if you need tight tolerances, want to make commercial items, are casting jewelry, or just have splash cash.
- Download one of the slicers and throw in some STLs to get a better idea on the build volumes.
https://preview.redd.it/wlkqqesp9ga81.png?width=1000&format=png&auto=webp&s=639894d9a7c6ab590b8b3a04890aa096f195803b
FDM
I have a low budget and want to get into 3D printing ($200):
A printer like the Artillery Hornet, Elegoo Neptune 2, or Anycubic Mega Zero 2.0 will allow you to affordably enter the realm of 3D printing but without many of the quality of life features.
*Ideal for: general prints, trinkets, fixtures, and light-functional p
Do your worst!
I'm surprised it hasn't decade.
For context I'm a Refuse Driver (Garbage man) & today I was on food waste. After I'd tipped I was checking the wagon for any defects when I spotted a lone pea balanced on the lifts.
I said "hey look, an escaPEA"
No one near me but it didn't half make me laugh for a good hour or so!
Edit: I can't believe how much this has blown up. Thank you everyone I've had a blast reading through the replies 😂
It really does, I swear!
Buenosdillas
They’re on standbi
Pilot on me!!
Dad jokes are supposed to be jokes you can tell a kid and they will understand it and find it funny.
This sub is mostly just NSFW puns now.
If it needs a NSFW tag it's not a dad joke. There should just be a NSFW puns subreddit for that.
Edit* I'm not replying any longer and turning off notifications but to all those that say "no one cares", there sure are a lot of you arguing about it. Maybe I'm wrong but you people don't need to be rude about it. If you really don't care, don't comment.
When I got home, they were still there.
What did 0 say to 8 ?
" Nice Belt "
So What did 3 say to 8 ?
" Hey, you two stop making out "
I won't be doing that today!
[Removed]
You take away their little brooms
This morning, my 4 year old daughter.
Daughter: I'm hungry
Me: nerves building, smile widening
Me: Hi hungry, I'm dad.
She had no idea what was going on but I finally did it.
Thank you all for listening.
There hasn't been a post all year!
I don't want to step on anybody's toes here, but the amount of non-dad jokes here in this subreddit really annoys me. First of all, dad jokes CAN be NSFW, it clearly says so in the sub rules. Secondly, it doesn't automatically make it a dad joke if it's from a conversation between you and your child. Most importantly, the jokes that your CHILDREN tell YOU are not dad jokes. The point of a dad joke is that it's so cheesy only a dad who's trying to be funny would make such a joke. That's it. They are stupid plays on words, lame puns and so on. There has to be a clever pun or wordplay for it to be considered a dad joke.
Again, to all the fellow dads, I apologise if I'm sounding too harsh. But I just needed to get it off my chest.
It’s pronounced “Noel.”
After all his first name is No-vac
What, then, is Chinese rap?
Edit:
Notable mentions from the comments:
-
Spanish/Swedish/Swiss/Serbian hits
-
French/Finnish art
-
Country/Canadian rap
-
Chinese/Country/Canadian rock
-
Turkish/Tunisian/Taiwanese rap
There hasn't been a single post this year!
(Happy 2022 from New Zealand)
Nothing, it just waved
