Can't get/keep APM enabled on A88M-G/3.1 with A10-7860K. CPU multiplier gets stuck at 33x.

Support for this CPU was added very late in the motherboard's lifetime; it's only available in a beta BIOS. I can sometimes get APM working for a while after clearing BIOS settings, but sooner or later it ends up disabled even when set to enabled. When that happens, the multiplier gets stuck at 33x. (I don't know if this is directly caused by APM being disabled or if there's some underlying problem that leads to the CPU multiplier being stuck and APM being disabled. Guessing the former, but trying to keep an open mind.)

Does anyone have any troubleshooting suggestions other than wiping BIOS settings every so often? Thanks.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Kufat
๐Ÿ“…︎ Jan 16 2022
๐Ÿšจ︎ report
Is it normal for my cpu multiplier and speed to be changing that much on idle? (I7 - 9700k) v.redd.it/akpmspa14m381
๐Ÿ‘︎ 106
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/PcGuyRay
๐Ÿ“…︎ Dec 04 2021
๐Ÿšจ︎ report
CPU multiplier borked in Windows

Windows OS capping my CPU multiplier to 11x limiting speed to 2ghz. I've reset the BIOS, and reinstalled Windows 10, Linux goes at full speed no issues.

Hope that somebody can figure this out, I've had no luck and the reinstall was my last hope for fixing it myself. Thanks in advance.

Rig:
AMD FX 8350
MSI 970 Gaming
32gb Kingston Fury HyperX
MSI GTX 1080
Samsung 500gb sata SSD
Hitachi 1tb HDD
2x WD Blue 1tb HDD
Generic WiFi card.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Chrykal
๐Ÿ“…︎ Jan 08 2022
๐Ÿšจ︎ report
[A+ Question] If the CPU runs at a multiplier of the Motherboard's system clock of say, 100Mhz, why can't I just overclock the system clock to 200Mhz and not put as much stress on the CPU?
๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/MF_Nook20
๐Ÿ“…︎ Dec 06 2021
๐Ÿšจ︎ report
Is the CPU clock multiplier supposed to change depending on load?

So recently I had an issue with my Alienware M15 R3 where the CPU clock speed sits at 4100 mhz (x42 multipler) and stays there, no matter what. It caused temperature and performance issues so I went into BIOS and disabled intel speedstep and intel speedshift. All is well, the temperature issue is gone and my PC sits at a good x26 clock multipler. But now, the clock speed does not change when i overclock, benchmark or anything. Here is my benchmark result and CPU-Z stats. Am I being stupid and that clock speed was not supposed to change to begin with, or is something up?

Edit: I've made a more detailed post on Tom's hardware forum.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/vTastyBleach
๐Ÿ“…︎ Dec 25 2021
๐Ÿšจ︎ report
Bought a new pre-built, does the CPU core speed and multiplier mean it's factory over-clocked? Is it a safe amount for an i7 11700kf? Thanks. Picture inside. imgur.com/6Aot6hE
๐Ÿ‘︎ 5
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/hondaexige
๐Ÿ“…︎ Nov 05 2021
๐Ÿšจ︎ report
Hol up so I can't change my cpu multiplier?
๐Ÿ‘︎ 11
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Nightmare_Vortex
๐Ÿ“…︎ Jul 04 2021
๐Ÿšจ︎ report
Youtube image freezing after increasing CPU multiplier.

Hello guys!

First off all I want to say I pretty much don't know anything about OC.

I own an older build and currently can't afford a better one.

intel i5 760

8GB single Channel DDR3 1333 MHz

Asus P7P55D-E LX (LGA1156) Mobo

NVIDIA GeForce GTX 1060 3GB

I'm guessing my CPU is kinda a bottleneck even for that GPU.

My cheap SSD got corrupted couple days ago and I replaced it with Samsung SATA SSD 870 EVO 250GB and installed fresh win 10.

I also bought some thermal paste and applied it after removing the old.

So i wanted to get a better performance on some games which use CPU like CSGO and alike.

I went into te BIOS and only thing I did was change the CPU multiplier so that my CPU was running on 3,3GHz instead of 2,8 GHz. I didn't want to bother with anything else so I left it on auto.

I ran a OCCT Bechmark for an hor and my CPU didn't go past 83ยฐ.

CSGO performance did increase on average by 20%.

But since then I have YT image freezing on chrome and opera, on microsoft edge it's still fine. Sound doesn't cut out and PC still works normally.

I would like to keep my CPU at 3,3 GHz but does anyone have an idea why is this happening?

Do you have any tips for "overclocking" and should I be more careful? I didn't mess with BCKL freq. and other stuff since it's and old rig and I don't want to ruin it. I think it's on 150 now.

Thank you for your time!

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/but_why_3885
๐Ÿ“…︎ Jul 16 2021
๐Ÿšจ︎ report
Having a motherboard with locked multiplier (like A320) means I shouldn't be able to change my CPU speed to be higher or lower, right?

If what I said in the title is correct then I am very confused because I can go down.

I am currently running my 2600X at 3.14ghz with my gigabyte a320m-h rev 1 with the latest bios (F53).

Here is a screenshot

๐Ÿ‘︎ 3
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/rpstforhire
๐Ÿ“…︎ Jun 19 2021
๐Ÿšจ︎ report
OpenBSD not using CPU multiplier I set in BIOS

Windows picks up my settings just fine and sets me to 4.2ghz at 1.4v under high load.

With apm -A it never goes higher than 3.3ghz, and running apm -H locks me to my standard 3.3ghz at 1.24v.

i5-2500k

dmesg:

OpenBSD 6.9-current (GENERIC.MP) #477: Sat Apr 24 16:08:13 MDT 2021
    deraadt@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 8539095040 (8143MB)
avail mem = 8264925184 (7882MB)
random: good seed from bootblocks
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xeb1d0 (105 entries)
bios0: vendor American Megatrends Inc. version "3801" date 09/12/2013
bios0: ASUSTeK COMPUTER INC. P8P67 LE
acpi0 at bios0: ACPI 4.0
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP APIC MCFG HPET SSDT SSDT SSDT
acpi0: wakeup devices UAR1(S4) P0P1(S4) RP01(S4) PXSX(S4) RP02(S4) PXSX(S4) RP03(S4) PXSX(S4) RP04(S4) PXSX(S4) RP06(S4) PXSX(S4) RP07(S4) PXSX(S4) RP08(S4) PXSX(S4) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz, 3300.49 MHz, 06-2a-07
cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,DEADLINE,AES,XSAVE,AVX,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 100MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.1, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz, 3300.03 MHz, 06-2a-07
cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT,DEADLINE,AES,XSAVE,AVX,NXE,RDTSCP,LONG,LAHF,PERF,ITSC,MD_CLEAR,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,MELTDOWN
cpu1: 256KB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 4 (application processor)
cpu2: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz, 3300.03 MHz, 06-2a-07
c
... keep reading on reddit โžก

๐Ÿ‘︎ 5
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/AmbassadorKoshSD
๐Ÿ“…︎ Apr 26 2021
๐Ÿšจ︎ report
I made a 16 bit multiplier and hooked it up to my WIP CPU reddit.com/gallery/hxss8s
๐Ÿ‘︎ 81
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/TheWildJarvi
๐Ÿ“…︎ Jul 25 2020
๐Ÿšจ︎ report
Cpu multiplier drops when performing memory or caches stress tests (aida64)

I'm having something occur that I don't quite understand! First...

Specs

Lan Li Lan Cool II Mesh

Asus Rog Strix z490-A Gaming

I have a i5 10600k

Enermax liqmax iii 360

Thermaltake Though Ram 4400Mhz on XMP I

my gpu was DOA so I'm waiting for another, running on integrated graphics,

I have tried a variety of OC setting with similar results, but for now I've gone back to default and only changed the following

multi core enhancement Disabled

Manual OC All Core ration 51 (for 5.1 Ghz )

Vcore 1.38v

And when I run AIDA64's Stress test CPU Only it runs at 5.1ghz and shows 1.385v

but if I add Cache, or memoery the cpu multiplier and speed start chaning, droping to x46 4.6ghz.

I've also tried turning off Speed-Step, Speed-shift and C-state but it didn't seem to matter. Also if I turn off turbo the OC settings don't seem to have any impact and the cpu just runs at 4.1ghz. Anyway I'm mainly trying to figure out why the when I add in the Cache or mem stress tests the CPU speed starts dropping/the multiplier goes down.

Anything thoughts? Could it be because I'm running on intergrated graphics atm?

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/thissjus10
๐Ÿ“…︎ Feb 27 2021
๐Ÿšจ︎ report
CPU Clock Multiplier drops after starting PUBG

I have R7 2700X CPU running on 4200MHz and few days ago I've notice my clock speed drops every time I start PUBG. The multiplier drops from 42x to 38x. My temps are around 45-50ยฐC while running PUBG, and the CPU utilization is around 30%.

If I start any other game or Cinebench (to stress test my CPU to 100%) the clock speed stays normal, so I've come to conclusion it has to be something with the game/anti cheat.

Any suggestions or ideas?

๐Ÿ‘︎ 10
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/-AreYouKittenMe-
๐Ÿ“…︎ Sep 27 2020
๐Ÿšจ︎ report
CPU Multiplier stuck at 4 (400MHz/core)

Hello,

I have an Acer Spin 5 laptop. I'm currently reinstalling windows on it but that isn't working because it's been installing for 2 hours now... My CPU multiplier is stuck at 4. Every core runs at 400MHz at boot it goes up to 34 (3.4GHz) for a really short moment and then it just drops to 4 and it's never coming up again.

I reset my bios settings to factory defaults as well to no avail. I checked my power settings and put the CPU minimum to 100% also no avail. Power saving isn't it either, the battery isn't the best anymore but it still more than okay.

I'm starting to think something in the hardware broke. Anyone has any ideas on what to do?

~Yami_Bas

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Yami_Bas
๐Ÿ“…︎ Feb 24 2021
๐Ÿšจ︎ report
Unable to change cpu multipliers and voltages in bios.

I'm using the MSI B450M DS3H with the Ryzen 5 1600 and have been trying to overclock it for a while now. I know what I need to do but everything I need is greyed out. I've tried circumvent it with ryzen master and easy overclock but those never save after a restart. Any help is appreciated and I'll provide what I can if you need.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/zzlgaming1
๐Ÿ“…︎ Mar 03 2021
๐Ÿšจ︎ report
FX-8350, MB fails POST when I change the CPU multiplier.

I have a fairly old FX-8350 nestled in an Asus Crosshair V Formula-Z motherboard. It's starting to show its age in newer games, so I'm trying to squeeze a little more power out of it by overclocking. The thing is, despite being a Black Edition processor and having an unlocked multiplier, I can't get it power on with any value other than the default 20x. Up to 21x, down to 19x, no POST, just a solid red LED next to the CPU. Not even an error code on the fancy Q Code display, just "00". Anyone seen anything like this before?

Note: I was able to overclock it by increasing the bus speed, and it runs stable up to 220 MHz (4.4 GHz) without adjusting any other settings in the BIOS. But I'm lazy and I don't want to start tweaking RAM timings and other settings to push the bus speed higher if I don't have to. I just want to bump up the multiplier, give it some voltage and let it run.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/AratanAenor
๐Ÿ“…︎ Dec 27 2020
๐Ÿšจ︎ report
Get Intel CPU multiplier or base clock without third party tools nor root access.

I looked at /sys, but I didn't find both.

I can do the multiplier calc myself, but, for that, I need to get the current base clock, which fluctuates from 99,00MHz to 100MHz. Some third party tools call it "clock" or "external clock"

Edit:

There no feasible solution for someone that doesn't know how to handle deep stuff like MSR register. I end up using the nominal base clock of 100MHz.

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/lucasrizzini
๐Ÿ“…︎ Oct 10 2020
๐Ÿšจ︎ report
I made a 16 bit multiplier and hooked it up to my WIP CPU reddit.com/gallery/hxss8s
๐Ÿ‘︎ 6
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/TheWildJarvi
๐Ÿ“…︎ Jul 25 2020
๐Ÿšจ︎ report
I know it's barely an overclock compared to most of the stuff around here, but I'm surprised I was able to undervolt my CPU and at the same time raise the multiplier to get 3 GHz. I'm getting really low temps and a nice boost in performance.
๐Ÿ‘︎ 39
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/AndroidUser37
๐Ÿ“…︎ May 20 2020
๐Ÿšจ︎ report
I cant change the cpu multiplier in the bios.
๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/spiderbitehere
๐Ÿ“…︎ Aug 15 2020
๐Ÿšจ︎ report
using the BIOS CPU multiplier

Are there any drawbacks to simply just increasing the CPU multiplier in BIOS and test how the CPU is performing? Does it have to be more complicated than that? I am not after pushing my CPU to its limits I just want it to perform a bit better, at the moment.

๐Ÿ‘︎ 5
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Electrohmmmm
๐Ÿ“…︎ May 29 2020
๐Ÿšจ︎ report
RNGSUS is my dad (I bet all stadium CPU's with no X multipliers and just this deck) I got rly lucky and somehow bet the final cpu
๐Ÿ‘︎ 13
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/We_win_these
๐Ÿ“…︎ Jun 07 2020
๐Ÿšจ︎ report
When trying to oc my i5 9600k, I canโ€™t change the cpu multiplier.

Edit: Your not supposed to click it, your supposed to use buttons like shift+ + or - also just typing a number while selected works

It is stuck on auto, I canโ€™t change it, double click it, press enter, nothing. How do I activate the oc?

๐Ÿ‘︎ 3
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/GlassJackhammer
๐Ÿ“…︎ Jul 24 2020
๐Ÿšจ︎ report
Is this a good Cinebench R20 score for a laptop? And any obvious errors in setup from the data? (i7-9750h, 32Gb, RTX 2070, 1TB Samsung M.2) CPU multipliers set from 4.2 to 3.6 all. undervolted as best I can.
๐Ÿ‘︎ 4
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Fred_Dibnah
๐Ÿ“…︎ Mar 30 2020
๐Ÿšจ︎ report
2004 Update causes fixed CPU Multiplier?

Hi,

I updated several days ago and today I had some very weird issues (in general just being extremely slow after ~30 minutes) and couldn't diagnose any issue. CPU and RAM usage was fine. But what I did notice was that the CPU speed wasn't going down as it normally was. It was locked to 4.35 GHz (according to AIDA64 a CPU Multiplier of 44x).

After reverting back to 1909 (thankfully the feature to revert to a previous version wasn't greyed out) the CPU multiplier happily jumps according to actual usage.

I just wanted to ask here if this is a known problem (I couldn't find anything with a quick google search for Update 2004, found the inverse (underclocking) from 2008 though)

To answer some question/remarks that may come:

No I don't have any other evidence other than what I already listed above (and I didn't take any screenshots)

Yes this may be circumstantial evidence.

No I don't have any kind of logs.

No my CPU isn't overclocked, it's a normal i7-8700k

No I'm not sure if my slowness issues were fixed with the revert (I only just did that), but my gut feeling is that it is linked to the multiplier issue

EDIT: Just found out that my father's laptop also seems to have this issue, for him it's stuck at 34x and not moving from there.

๐Ÿ‘︎ 4
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/WonaBee
๐Ÿ“…︎ Jun 09 2020
๐Ÿšจ︎ report
[Newbie question] Why don't we increase voltage first to find the thermal limit, THEN increase the CPU multiplier?

I just got into overclocking in the last week so forgive my ignorance. I've read a ton of articles, and I'm confused by one part of the process. All the guides recommend that you iterate the CPU multiplier and voltage temps in small increments, check temps under load, and then check stability. Overclocking requires patience, but this seems to be excessively long.

If the temps are (primarily?) related to voltage, then why don't you increase the voltage first to the point where temps are within limits, THEN increase the CPU multiplier to its highest stable point? It seems to me that this would drastically shorten the process because you'd have your temps under control first, then you could focus on stability.

To reiterate, the process would look something like this:

  1. Increase voltage incrementally until temps are maintaining just under 80 degrees under load (e.g., Prime95 Small FFT). This is now your max safe voltage.

  2. Increase CPU multiplier incrementally. Keep an eye on temps. Check stability under load (e.g., Prime95 blended test).

  3. Once stable, see if you can drop voltage a bit without compromising stability. Otherwise, return to voltage from step 2.

I assume that it's because they're related somehow, but I'm not quite getting it yet.

Edit:

Thanks everyone for the good info!

  1. I was wrong about the 80 degree target in step 1. Increasing to max temp is dumb because increasing the clock will increase heat too. Maybe 65-70 degrees would be better?

  2. I still think that increasing voltage by some amount first has to be valuable unless you want to spend 80 hours overclocking. Maybe I'm just too impatient, but moving up 100 MHz and .005 V at a time is just ridiculous given my experience with this particular machine and how far I had to go to bump it up from 3.4 to 4.4 GHz.

๐Ÿ‘︎ 7
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/sometimesynot
๐Ÿ“…︎ Jan 16 2019
๐Ÿšจ︎ report
Overclocking cpu with locked multiplier

I have seen some posts about slight overclocking non k cpus and i have an i5 7400 and i want to overclock it I tried following their steps but i cant see anything in the bios about Bclk i did however see something that said cpu ratio that said its used to determine the cpu clock speed i tried clicking it but it doesnt do anything

Is there anyway i could slightly overclock this?

Btw i have a B250M Pro Vd

๐Ÿ‘︎ 5
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/iVolgen
๐Ÿ“…︎ Apr 30 2020
๐Ÿšจ︎ report
Low CPU multiplier

I updated to the 1.0.0.4B BIOS last night and after waking my desktop up this evening I'm seeing what looks to be a much lower CPU speed and multiplier than I would have expected. Is this normal or should it be running at least at 3600Mhz with a higher multiplier constantly? I built the system last weekend so I'm still getting used to what can be considered as typical. This is running on a Tomahawk MAX.

https://preview.redd.it/mbb8eeh2g5w31.png?width=408&format=png&auto=webp&s=486bedd608dcd5c1770f060d2b189ffaac641d39

๐Ÿ‘︎ 4
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/cannedkarma
๐Ÿ“…︎ Nov 01 2019
๐Ÿšจ︎ report
CPU running at lowest multiplier

I have this pretty old laptop that i installed with Windows 10 recently, but i notice that the CPU always running at 0.80 GHz ever since. I did some digging and found a temporary solution using ThrottleStop and disable BD PROCHOT which is something to do with the temperature based on what i read. The thing is it never happened when i'm using Windows 7 and i never seen it throttle because of temperature either. IIRC i used to play game with this laptop and the tempt can get around 68-70C and it doesn't throttle.

I wanna know what's causing this and whether it's possible or not to solve this issue so i don't have to keep running ThrottleStop everytime i turn on the laptop. And the funny part if i disable the BD PROCHOT it will run at the highest multiplier even at idle no matter what power plan i use. The laptop is Dell Inspiron 3442.

๐Ÿ‘︎ 3
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/hazuja
๐Ÿ“…︎ Oct 22 2019
๐Ÿšจ︎ report
[HELP] i9 9900k poor benchmark/immediate shutdown in Prime95 over 47 CPU multiplier

I am new to this sub and new to overclocking, so I will try to be detailed, bear with me.

I recently built a PC with the following parts:

  • Intel - Core i9-9900K 3.6 GHz 8-Core Processor
  • Gigabyte - Z390 AORUS MASTER ATX LGA1151 Motherboard
  • Asus - GeForce RTX 2080 Ti 11 GB ROG Strix Gaming OC Video Card
  • Corsair - H150i PRO 47.3 CFM Liquid CPU Cooler
  • ARCTIC - MX4 4 g Thermal Paste
  • Corsair - Vengeance RGB Pro 32 GB (2 x 16 GB) DDR4-3200 Memory
  • [Western Digital - SN750 1 TB M.2-2280 Solid State Drive
  • Seagate - FireCuda 2 TB 3.5" 7200RPM Hybrid Internal Hard Drive
  • Corsair - Obsidian 500D RGB SE ATX Mid Tower Case
  • Corsair - 1000 W 80+ Gold Certified Fully-Modular ATX Power Supply
  • x6 Corsair LL120 RGB Fans (Replaced H150i stock ML120 fans)
  • Microsoft - Windows 10 Home 64-bit

I want to overclock the i9 9900 to increase performance while still being stable. I watched some videos specific to the Gigabyte boards and heavily followed this guide from Gigabyte: https://www.gigabyte.com/FileUpload/Global/multimedia/2/file/525/946.pdf

To start, I followed those instructions almost exactly. Specifically:

  • I boosted memory to 3200 MHz (Per specs)
  • I set multiplier to 50 (5GHz)
  • Set Uncore ratio to 47
  • Disabled Intelยฎ Speed Shift Technology, CPU Enhanced Halt (C1E), C3 State Support, C6/C7 State Support, C8 State Support and C10 State Support
  • Disabled VT-d
  • Disabled Enhanced Multi-Core performance
  • Disabled "Ring to Core"
  • Set CPU Vcore LLC to Extreme
  • Set CPU Vcore to 1.300v

There may have been a few other tweaks, but this is mostly where I started. This setup posted just fine, and I was getting 4.9-5.0GHz in Task Manager when I booted.

First, I ran userbenchmark. My i9 9900k was showing between 13% and 18% in UB, and well below average on the curve.

I then opened up CoreTemp and Prime95. Starting Prime95, my computer would just immediately power off, no BSOD. Before shutting off, I noticed that the thermals were spiking up above 90 and potentially hitting the t.j. Max value. I then went back into BIOS and reduced the CPU Vcore to 1.200v, and I dropped the multiplier one value at a time. At 47 multiplier, on 1.200v, I was able to run Prime 95, but my thermals range from 84-94 C.

Once I had this setup, I reran userbenchmark, and I am still getting between 13% and 18%, and showing serious under-performance.

Frankly, I am at a loss. I as

... keep reading on reddit โžก

๐Ÿ‘︎ 2
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/Oliverkahn987
๐Ÿ“…︎ May 06 2019
๐Ÿšจ︎ report
What settings to change here to make it so that my CPU is adaptive voltage and multiplier?

CPU: i7-4790k

Mobo: Asrock Z97 pro4

So I have spent the better part of 2 hours trying to figure out how to set my mobo settings so that when my PC idles, the CPU takes down its voltage and core multiplier. My current overclock is 4.5 Ghz and 1.25 volts and I am happy with it. How do I make my mobo force my cpu to decrease multiplier and decrease volts when its idle but max out to 4.5 Ghz and 1.25 volts again for when I game and stuff?

My mobo is weird so I take pictures of all the related settings I can find and hopefully you guys can tell me if I should change any of them.

MOBO Settings:

1: https://prnt.sc/ktrgbi

2: https://prnt.sc/ktrgd2

3: https://prnt.sc/ktrger

4: https://prnt.sc/ktrgfz

5: https://prnt.sc/ktrggz

6: https://prnt.sc/ktrgi1

So? Anything I am missing or should enable/disable? Its weird cos on my old 4690k I did manage to make it so that it takes down the multiplier when not required but i don't know why its not doing it on the 4790k...

๐Ÿ‘︎ 6
๐Ÿ’ฌ︎
๐Ÿ‘ค︎ u/yourdeath001
๐Ÿ“…︎ Sep 13 2018
๐Ÿšจ︎ report

Please note that this site uses cookies to personalise content and adverts, to provide social media features, and to analyse web traffic. Click here for more information.